Part Number
177-0947
Special Price $100.91 Regular Price $112.12
---------OR---------
In stock
Only 2 left
Estimated Ship Date: 1 Business Day or Less
ACDelco GM Original Equipment Brake Drums are cylinder shaped bowls where the wheel cylinder presses the brake shoes outward against the inside of the drum. Drums are typically found on older vehicles and on the rear axles of trucks and some cars. These original equipment brake drums are manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ? WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov
BRAND: ACDelco
FEATURES:
- Chevrolet;Pontiac;Saturn
- GM-recommended replacement part for your GM vehicle's original factory component
- Have a rust-preventative coating to help protect against corrosion
- Inspected for balance, resulting in smooth brake operation and noise reduction
- Manufactured to GM OE specification for fit, form, and function
- Offering the quality, reliability, and durability of GM OE
SPECIFICS:
Bolt Circle Diameter (in) | 3.937008 |
Bolt Circle Diameter (mm) | 100 |
Bolt Hole Quantity | 4 |
Drum Center Bore Diameter (in) | 2.246457 |
Drum Center Bore Diameter (mm) | 57.06 |
Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems. |
Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
Height (in) | 3.38 |
Length (in) | 13.12 |
Material | Cast Iron |
Mount Hole Diameter (in) | 0.5511811 in |
Mount Hole Diameter (mm) | 14 mm |
Programming Required | No |
Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Squealing or scraping noises. |
Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Brake pedal pulsation (not to be confused with normal ABS operation). |
Weight (lb) | 11.29 |
Width (in) | 12.38 |
DOWNLOADS:
APPLICATIONS:
- 2007-2007 Chevrolet Cobalt - Position: Rear
- STEEL WHL(PG1)
- 2008-2008 Chevrolet Cobalt - Position: Rear
- SOFT RIDE SUSP(FE1), ALUM WHL(PFD), STEEL WHL(PG1)
- 2005-2006 Pontiac Pursuit - Position: Rear
- SOFT RIDE SUSP(FE1), Cast Iron
- 2007-2007 Pontiac G5 - Position: Rear
- STEEL WHL(PG1)
- 2005-2008 Chevrolet Cobalt - Position: Rear
- SOFT RIDE SUSP(FE1), Cast Iron
- 2003-2007 Saturn Ion - Position: Rear
- 2007-2008 Pontiac G5 - Position: Rear
- SOFT RIDE SUSP(FE1), Cast Iron
- 2008-2008 Pontiac G5 - Position: Rear
- SOFT RIDE SUSP(FE1), ALUM WHL(PFD), STEEL WHL(PG1)
Customer Questions
Compatible Vehicles
Year
Make
Model
Engine