Cardone 13-2571 | Brake Master Cylinder
Part Number
13-2571
$66.99
Out of stock
Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE® New Master Cylinders to match O.E. performance. Supplied with new O.E.-quality seals and cups, each unit is endurance-tested to ensure perfect fit, function and reliable performance.
BRAND: Cardone New
FEATURES:
- Brake Master Cylinder
- New Brake Master Cylinder
- Master Cylinder, Brake Master Cylinder, MC, Master, Cylinder, Power Brake Master Cylinder, Hydrualic Master Cylinder, Manual Brake Master Cylinder
- Acura CL 1997, TL 1996-95, Vigor 1994-92; Honda Accord 1997-91, Odyssey 1997-95, Prelude 1996-92; Isuzu Oasis 1997-96
- Brake Master Cylinder
- New Brake Master Cylinder
SPECIFICS:
| Bore Diameter (N) | 1.000" |
| E-Waste | No |
| FAQs | Check booster for a defective push rod seal. If this seal is bad, it could drain the brake fluid out of the master cylinder. |
| FAQs | Check the steering and suspension. Inspect both calipers for binding or sticky slides or pins. Check brake lining for oil/grease or uneven wear. Inspect brake hoses for restriction. Check for proper tire pressure. |
| FAQs | Does a step bore style master cylinder require a specific bleeding process? |
| FAQs | Dot 3 and 4 are Glycol-based fluids and Dot 5 is a silicone-based fluid. |
| FAQs | How can I test a master cylinder to see if it's bypassing? |
| FAQs | Most likely, the fluid in the system is contaminated. The most common form of contamination occurs when petroleum-based fluid has been accidentally introduced into the brake system. If that has happened it is almost certain that all rubber components in the brake system (hoses, seals, bladders) will need to be replaced after the system is thoroughly flushed. If the contamination is due to moisture, rust and/or dirt, it might be possible to restore operation by flushing the system and replacing the brake fluid with fresh, clean fluid. Always use the manufacturer-recommended brake fluid from a sealed container. |
| FAQs | Simply plug the master cylinder ports and press the brake pedal. If the master cylinder is bypassing, the pedal will go down. If the pedal stops hard, the master cylinder is OK. |
| FAQs | What causes the car to pull to one side during braking? |
| FAQs | As a rule, always use the brake fluid recommended by the O.E. which is stamped on the master cylinder lid. Note: Always use new fluid from a sealed container. |
| FAQs | I replaced the master cylinder and now the pedal is high and hard. Why? |
| FAQs | One side of my front brakes won’t release, why? |
| FAQs | Replace all brake fluid. Brake fluid is hygroscopic which means it absorbs moisture. Too much water in brake fluid will cause vapor lock and apply pressure to the wheels. Also check for proper push rod adjustments and stop light/cruise control switch adjustments. |
| FAQs | The brake pedal is low and spongy. Is it a bad master cylinder? |
| FAQs | What type of fluid should I use: DOT 3, DOT 4 or DOT 5? |
| FAQs | First, check for air in the system. Make sure master cylinder is level when bleeding. Air will compress in a hydraulic system causing a low pedal. Then, check for brake hose swelling or expanding under pressure. Next, check brake drums/discs for proper specifications. Finally, check brake material. |
| FAQs | My original master cylinder leaked out of the back of the piston into the booster area. Why? |
| FAQs | The master cylinder is working correctly. Check for a faulty brake booster or frozen wheel cylinder/caliper. |
| FAQs | This is caused by a problem with the caliper or a brake hose. |
| FAQs | The first step to bench bleeding a step bore is to slowly depress the master cylinder piston, then release slowly and wait 20 seconds before depressing again. NEVER pump piston/pedal with a step bore style master cylinder. Follow the same process on the vehicle. |
| FAQs | What causes the brakes to lock up after only a couple of miles? |
| FAQs | What’s the difference between Dot 3, 4 and 5? |
| FAQs | Why is the piston stuck inside the bore of my master cylinder? |
| Features and Benefits | Plastic reservoirs are vacuum-tested to ensure they are leak free |
| Features and Benefits | Seals are temperature-cycled from -30°F to +220°F to ensure reliable performance during your daily commute |
| Features and Benefits | Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure |
| Features and Benefits | Mounting hardware and bleeding kits are supplied with every unit to make the installation and bleeding process faster and easier (where applicable) |
| Features and Benefits | Castings feature a premium protective coating to minimize corrosion and extend unit life |
| Features and Benefits | Only O.E.-quality seals and cups are used to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications |
| Installation Hardware Included | No |
| Master Cylinder Color/Finish | Gray |
| Master Cylinder Material | Aluminum |
| Mounting Hole Quantity | 2 |
| Package Contents | Master Cylinder |
| Pedal Rod Included | No |
| Port Quantity | 2 |
| Primary Port Size | M12 x 1.0 |
| Product Condition | New |
| Reservoir Included | Yes |
| Reservoir Material | Plastic |
| Reservoir Type | Single |
| Secondary Port Size | M10 x 1.0 |
DOWNLOADS:
INTERCHANGE:
- Honda: 46100SM4G54
- Honda: 46100SS0A52
- Isuzu: 5862055090
- Acura: 46100SM4G53
- Acura: 46100SM4G54
- Honda: 46100SM4G52
- Honda: 46100SM4G53
APPLICATIONS:
- 1996-1997 Isuzu Oasis
- 1991-1997 Honda Accord
- 1992-1996 Honda Prelude
- 1992-1994 Acura Vigor
- 1995-1997 Honda Odyssey
- 1997-1997 Acura CL
- 1995-1996 Acura TL
Customer Questions
Compatible Vehicles
Year
Make
Model
Engine